World-Designs-Forum  

Go Back   World-Designs-Forum > World Designs > Problems
Register FAQ Members List Calendar Gallery Today's Posts Search Today's Posts Mark Forums Read

Problems For questions and answers re World Designs Projects

Reply
 
Thread Tools Display Modes
  #31  
Old 9th May 2016, 01:55 PM
bob orbell bob orbell is offline
Senior Member
 
Join Date: Nov 2009
Location: kettering northants.
Posts: 1,450
Default Re: KEL 84 Strange Noises

Aha, you'r just a wimp Philip, but a nice wimp.
Reply With Quote
  #32  
Old 9th May 2016, 02:02 PM
bob orbell bob orbell is offline
Senior Member
 
Join Date: Nov 2009
Location: kettering northants.
Posts: 1,450
Default Re: KEL 84 Strange Noises

Quote:
Originally Posted by deepdown130 View Post
I cycle mainly as a means of getting to the railway station to be honest. Not sure I get much pleasure out of it (due to other road users generally). I work in London and sometimes in Bath so it makes little sense to have a car at the moment.

I'm impressed you aim for 100 miles a week - you must be fitter than the proverbial butcher's dog!
Yes I know what you mean about other road users and cycles, but I do most of my miles on country lanes and some off road stuff, I started cycling big time about 4 years ago after a knee replacement, it was the best exercise for the knee and to get my power back after 15 years of pain and limping . BOB
Reply With Quote
  #33  
Old 9th May 2016, 06:00 PM
bikerhifinut bikerhifinut is offline
Senior Member
 
Join Date: Jan 2006
Location: Penrith, Cumbria
Posts: 828
Default Re: KEL 84 Strange Noises

Just to stray back on topic.........lol lads dont lynch me.

Don't labour under a misconception that Edicron ECF80's as a replacement next time will be the same. Edicron are a well known rebrander and none the worse for that but there's no guarantee another pair will be the same origin.
Now I don't know if anyone else has broached this but what sort of DC heater supply have you got to the ECF80? If its the Schottky mod, then you really must have the pi filter in place as the voltage can get rather high. This might possibly stress the heaters and cause valve problems. I had a similar issue with a KEL84 that I bought used where the schottky mod hadn't had the pi filter with it. out of both sets of ECF 80 that came with it one of each pair was noisy and I figured the overvoltage on the heaters was the cause. After fixing it and getting the heaters down to 6.3v it stayed good. I used a set of generic Foreign made ECF80 and they seemed just fine to me. I think they originated from the service dept at the old radio factory in Southend (Ecko?) according to the friend who donated 4 to me. He'd got them from an old timer who worked there.
Anyway if you're happy with the way your edicrons work stick with them and dont worry about "spares" if you have them working inside their parameters they'll last years.

Andy.

Last edited by bikerhifinut; 9th May 2016 at 06:01 PM. Reason: clarification
Reply With Quote
  #34  
Old 9th May 2016, 08:35 PM
Richard Richard is offline
Super Moderator
 
Join Date: Dec 2005
Location: Notts
Posts: 4,500
Default Re: KEL 84 Strange Noises

Yes, as Andy says, check heater voltages.

If schottkies are used, part of any advantage would be from them being a low noise diode, and part of the advantage is in them dropping less voltage during rectification, so we end up with a bit under 1V extra. This can then be dropped in a pi filter which lowers noise further.

This info and the suggested 1R dropper resistor for KEL84 are in the faq, http://www.world-designs.co.uk/forum...read.php?t=573
__________________
'
Reply With Quote
  #35  
Old 9th May 2016, 09:42 PM
deepdown130 deepdown130 is offline
Junior Member
 
Join Date: Nov 2006
Location: Bristol
Posts: 16
Default Re: KEL 84 Strange Noises

Thanks for the further guidance chaps. I'm certainly learning a lot about the way my amp because of this "problem".

I measured the heater voltages on the 2nd May and they were both at 6.2V. That has drifted up 0.3V since I built it (although I'm guessing that could just be down to natural variations in the mains supply voltage).

My KEL is standard build from the original print - no mods.

Taking your advice about the valves lasting years I think I'll leave it as it is and have a tinker when they finally wear out.

I really do appreciate the advice, offers and help I've received (despite my tetchy moment - now deleted).

Thanks again

Gavin
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 03:25 AM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright World Designs