World-Designs-Forum

World-Designs-Forum (http://www.world-designs.co.uk/forum/index.php)
-   WD Amplifiers (http://www.world-designs.co.uk/forum/forumdisplay.php?f=40)
-   -   PRE PHONO PSU 3 umbilical sockets and wiring (http://www.world-designs.co.uk/forum/showthread.php?t=7885)

Richard 6th May 2020 09:15 PM

PRE PHONO PSU 3 umbilical sockets and wiring
 
Binder, that's the name Bob thanks, searched on that and found my notes, 4 pin are supplied and 5 pin can be used if you want a chassis earth,

Binder 678 plugs and sockets from Farnell

http://www.farnell.com/datasheets/19136.pdf

4 pin

chassis socket female 9906120004 Farnell 1122416
chassis socket male 9906110004 Farnell 1122410
cable connector female 9906100004 Farnell 1122404
cable connector male 9906090004 Farnell 1122398

5 pin

chassis socket female 9906160005 Farnell 1122417
chassis socket male 9906150005 Farnell 1122412
cable connector female 9906140005 Farnell 1122405
cable connector male 9906130005 Farnell 1122399

4 and 5 pin inserts are interchangeable within bodies

Farnel 1491512 5 core cable per metre LAPP KABEL - 1312005 - CABLE, OLFLEX, PU, 5CORE, 0.5MM, PER M

bob orbell 7th May 2020 06:42 AM

Re: WAD v, WD
 
Thanks Richard, I did buy some very flexible 5 core 0.5mm cable for my two PSU's umbilical cords, I remembered you doing such with yours, it dose make sense but have not got round to getting the plugs and sockets, too much time spent on prototype regulated HT, but I think I am there, almost. Bob

bob orbell 7th May 2020 08:26 AM

Re: WAD v, WD
 
Quote:

Originally Posted by Richard (Post 90795)
Binder, that's the name Bob thanks, searched on that and found my notes, 4 pin are supplied and 5 pin can be used if you want a chassis earth,

Binder 678 plugs and sockets from Farnell

http://www.farnell.com/datasheets/19136.pdf

4 pin

chassis socket female 9906120004 Farnell 1122416
chassis socket male 9906110004 Farnell 1122410
cable connector female 9906100004 Farnell 1122404
cable connector male 9906090004 Farnell 1122398

5 pin

chassis socket female 9906160005 Farnell 1122417
chassis socket male 9906150005 Farnell 1122412
cable connector female 9906140005 Farnell 1122405
cable connector male 9906130005 Farnell 1122399

4 and 5 pin inserts are interchangeable within bodies

Farnel 1491512 5 core cable per metre LAPP KABEL - 1312005 - CABLE, OLFLEX, PU, 5CORE, 0.5MM, PER M

An update to Richards part no's 9906150005 Farnell no is now 2949826
and RS Components now stock them 5 pin no's 129-8523
129-8804
129-8753
129-8472
Bob

bob orbell 9th May 2020 03:52 PM

Re: Lock Down
 
Richard, I have now got all the 5 pin plugs sockets cable etc, so I am thinking about this conversion and would ask what you did, HT pos, 0 volts, heater + and heater - are obvious, what about the earth lift resistor in PSU , did you remove it, leave it or what, I would like to think chassis earth and 0 volts should not be connected, comments please. Bob

Richard 9th May 2020 06:46 PM

Re: Lock Down
 
Hi Bob,

Check me through on this as it’s a while since I did mine.

Disconnect the 0V HT link from the case earth posts in Pre and Phono leaving just the PCB 0V still connected to the socket.

Use the new 5th wire for Mains Earth by connecting it to the case posts on Pre and Phono and to the new socket pin.
(I used the middle of the 5 pins for Mains Earth and kept the same order as original for the 4 existing ones. That way the orignal wiring instructions can be followed and the extra Earth cannot be read the wrong way around.)

PSU case earth post is already connected solidly to Mains Earth and your new 5th (middle) pin also connects to the case earth post. Leave the lift resistor in place. All that changes in PSU is the new Earth wire goes to chassis post.

You should now have the usual way of earthing with all cases at Mains Earth and 0V HT stood off by the 100R list resistor.

It helps to use Green/Yellow for the Mains Earth and Black for 0V if you’re replacing them.

Final check with a meter :)

bob orbell 9th May 2020 06:54 PM

Re: Lock Down
 
Thanks Richard, I have already wired the two umbilical's exactly as your description and will continue with the rest on Monday and follow your advise. By the way, have you seen the price of these connectors now :D'oh!:. Bob

Richard 10th May 2020 10:35 AM

Re: PRE PHONO PSU 2 and 3 umbilical sockets and wiring
 
Hi Bob, are those prices for singles? I'm sure they were about that for a bag of 5 when I did mine. I wonder if they're going short/stopping them?

bob orbell 10th May 2020 11:02 AM

Re: PRE PHONO PSU 3 umbilical sockets and wiring
 
Both Farnell and RS prices are for one unit, RS is a little more expensive, but I use them, two of each, total eight parts cost me 54.08 :D'oh!:, but it's only money and because I am not using any powered transport since November last year the bank balance has continued to rise, ;) . Bob


All times are GMT +1. The time now is 01:08 PM.

Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Copyright World Designs