World-Designs-Forum (
-   Problems (
-   -   KT88 construction problem (

A.N. Beal 6th September 2014 11:22 AM

KT88 construction problem
Dear Friends,

I have just completed wiring up a new KT88 XL amplifier and have a problem. I have set it up with dummy load resistors across the speaker terminals as directed and checked voltages. The left channel measures and behaves OK.

However on the right channel a gentle buzz develops after a minute or so and the dummy load resistors overheat. (I switch off when this happens.)
I have checked voltages and all are correct except for U2 pins 3 and 6, which measure 88-90v (left channel 84v) and U3 and U4 pins 8 which measure 48v (left channel 40v).

I have checked my wiring and resoldered a couple of joints but the problem remains. Any suggestions what the problem might be and what to check?

Richard 6th September 2014 02:59 PM

Re: KT88 construction problem
Hello :)

Heating of the load resistor shows an AC current is going through it. This may be from an external signal that is being amplified (RF) or an oscillation within the amp circuit itself.

1) Short the inputs with a shorted RCA plug or by attaching a CD player etc. I have had this myself with a Kit88 and yes the resistor gets hot by itself as you find.

2) It may be a bad valve causing oscillation. Swap U2 across channels and see if the problem stays or moves with the valve to the other channel. Swap U3 and U4, for a similar check, and then U1 also.

3) It could be oscillation within the amp itself. Check carefully that the output transformer wires are connected correctly and the feedback wire and components are correctly connected.

A.N. Beal 6th September 2014 04:25 PM

Re: KT88 construction problem
Dear Richard,
Thanks for your helpful reply.
1. I tried shorting the inputs - problem didn't change.
2. I tried swapping valves U2 and then swapping valves U3 and U4 but it was still the left channel load resistor that started to smoke. There is only one valve U1, so I couldn't swap this.
3. I checked continuity of all the output transformer and feedback wiring against the instructions using a multimeter and it all checked OK.
So no joy so far. Any further suggestions?

A.N. Beal 6th September 2014 05:09 PM

Re: KT88 construction problem
Extra information: I checked it with the volume control turned down to zero, which effectively short circuits the inputs. The left channel load resistor still overheated. A little before the load resistor starts smoking, as well as gently buzzing the amplifier also starts to emit a tone (I estimate the frequency as in the region of 500Hz).
Any help in tracking down the cause and solution would be welcome.

A.N. Beal 6th September 2014 05:46 PM

Re: KT88 construction problem
I have just measured the AC voltages across the dummy load terminals: a fraction of a volt on the right channel, 7 volts on the left channel.

John Caswell 6th September 2014 06:12 PM

Re: KT88 construction problem
With the amplifier turned off and the KT88s removed measure from Pin 5 of each KT88 to earth. Should read 220K or thereabouts. If not you have a wiring fault. Correct this and try again.
If you still have a problem disconnect the feedback link to C10/R18 on the faulty channel, if the problem goes away then the phase of the feedback is wrong and can be corrected in one of several ways. IF you are sure that you have wired the secondary of the output tx correctly then it is possible that you have the primary wired incorrectly or the two anodes feeds of the 5687 driver "**** about face" In which case swap one or the other reconnect feedback and try again. I would choose the 5687 anode feeds as the simplest method
The variations on U2 I suggest are within limits of 10%.
Let us know how you get on.
Have you spoken to Matthew about this? as I am involved indirectly


A.N. Beal 6th September 2014 07:05 PM

Re: KT88 construction problem
Dear John,

Thanks for your suggestions.

1. Resistances checked with valves removed - all about 230k ohm, assumed OK.
2. Reinserted valves, disconnected left channel feedback link - problem disappeared.
3. Now the strange part: I checked all the output transformer connections and they were all correct and the U2 anode connections were also correct.
4. Having failed to find anything in the wiring which appeared wrong, I took your advice and swapped the U2 anode connections.
5. Switched on and ... peace, quiet, no smoke, voltages fine, problem solved.

So thanks very much indeed for your help - I don't think I could have solved this one on my own.

Yes I had been in touch with Matthew about this, so it is the same one he spoke to you about.

Thanks and best wishes,


John Caswell 6th September 2014 07:50 PM

Re: KT88 construction problem
Hi Alasdair,
Sometimes my brilliance astounds even me - Yeah right!!!!!!!!!! once I was conceited now I'm perfect:D:D
No it is just looking at the problem and remembering things in the long distant past then offering suggestions based on experience.
Glad all has come good, enjoy, as it is a top class amplifier.


A.N. Beal 6th September 2014 09:21 PM

Re: KT88 construction problem
Another problem!

I connected up the amplifier to loudspeakers and switched on with high hopes. However although the left channel sounded good, the right channel was completely dead. I tried different sources and also swapping the speakers around but it is the amplifier and even with the volume control turned up full there is no sound at all from the right hand speaker. (There is slight hum and hiss from the left, as would be expected.) I reopened the amplifier and checked all resistances and voltages - perfect on both channels.

I have checked the output wiring and as far as I can see it is all OK.

Any suggestions?

John Caswell 6th September 2014 10:47 PM

Re: KT88 construction problem
Hi Alasdair.
The dead channel is the same one that was playing up?
Is it a plain amplifier or and integrated version?
When you say that you cannot hear anything is it completely silent?


All times are GMT +1. The time now is 09:59 PM.

Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.
Copyright World Designs